Tuesday, April 13, 2010

Hot wire polystyrene cutter for perfectly straight edges

I'm building the box that will contain the balloon's payload out of a polystyrene sheet. Polystyrene can be bought in construction supply stores such as Leroy Merlin in Europe, maybe Home Depot in the US. I've got a 160 x 60 cm sheet for about 2€ from Leroy Merlin (you have to go to the construction supply area, not the main shop).

You can cut polystyrene with a regular knife, but the easiest way is using a hot wire. At the right temperature, the wire melts the foam like butter, leaving the cleanest cut behind. And best of all, with no fumes!

There are some cool solutions out there based on soldering irons, these are ideal to cut small pieces of foam in shapes, but I want perfectly straight edges because I need to glue the box sides together. This is what I did:

Ingredients:

  • Nicrom wire. This is the cutting wire. Get it from a hairdryer or an electric heater. You can go to a recycling center and dig for one among the electronics garbage. That's how I've got mine, every time I go to the recycling place I bring more trash home than I drop off there :)
  • Car battery, or something capable of delivering 3-4 amps at 9-12 volts. I used my car's old battery. It won't power the starter, but it definitely melts the polystyrene.
  • A couple of battery cables with clamps.
  • 2 aluminum rods. 1 m long, 6-8 mm thick is enough. Hollow ones are cheaper, lighter and better. I've got them from a local hardware store for ~1.50€ each.
  • Small machine screws and bolts. I used 3mm across, 12mm long screws.
  • Two vises. Mine are small, the ones that will hold on to the bench with a clamp, rather than screws.
  • Drill or dremel tool. And a 3mm bit.

First, clamp the vises to the bench, one facing up and the other facing down. These will hold the rods.

Use one of the vises to clamp and flatten the tip of the rods. Just flatten the last 1-2 cm, this will make it easier to drill through it.

 

Cut the nicrom wire. The wire acts as a resistor, and the shorter you cut it, the hotter it will get. Hotter will cut the foam faster, but it does not have to be incandescent. In fact, if it's too hot, it can break. So it's better to err on the generous side, and if it doesn't get hot enough, you can cut it shorter later. I used about 50cm. My wire looked like a spring, so I decided to straighten just 15-20 cm and leave the rest coiled up.

Drill two holes with the 3mm bit on the rod's tips. Insert a screw through the hole and secure the nicrom wire to the rod with a bolt. Do it with both rods. The total length of the wire between the rods is 15-20 cm, so I have some coiled-up wire overhanging.

 

Clamp the two rods, one with each vise. Make sure the wire is tight. The aluminum rods are very flexible, so just tighten the wire until the rods bend a little. Also, make sure the wire is at a right angle with the bench. Try to straighten the wire as much as you can (at least the stretch that will cut through the polystyrene). Just press it between two fingers and slide the fingers down repeatedly.

Make sure the rods or the vises don't touch each other, or they will short the battery!

Now, hook up the cable clamps to the battery. You can try connecting the clamps directly to the rods, but the stretch of wire between them will probably be too short and the wire will get glowing hot in seconds. So I chose to hook up one clamp to a rod, then the other clamp to the overhanging wire. Just remember the closer the clamps are on the wire, the hotter it will get.

 

 

That's it... Use a plank as a guide (sort of like a T-square) if you need parallel edges. You can clamp the plank to the bench, so that you don't have to hold it and can focus on the cutting. Try not to stop as you cut, or you'll start melting a hole around the wire (check the fourth picture below, can you see the dents?). Just keep constant speed. You'll be surprised how extremely clean the cut is!

 

7 comments:

  1. Hi!

    Please, could you post some extra considerations about the reasons why you chose the ArgentData over the Radiometrix?

    Thank you!

    ReplyDelete
  2. Actually, I think I will be using the Radiometrix HX1 module, since it is much cheaper and this is my first flight, so I won't be throwing away too much money if I lose the payload.

    The MX146 is, in any case, a superior device. It can operate on multiple frequencies, and it can put out 500 mW (vs HX1's 300 mW).

    One known problem with the HX1 is that it drifts a lot with temperature. I don't know about the MX146, though.

    The thing is that a lot of people has used Radiometrix on balloons before and it's a proven technology, so I'm going to go with it. One thing I don't like about the MX146 is that the 8v version is pushing its PA stage to the limits, and can only withstand a few seconds of transmission. You will really burn it if you leave it keyed by mistake. Not a huge deal, but you have to be very careful with this.

    ReplyDelete

  3. - Đây là một giới tử có thể chứa được vật còn sống, ở Thần giới cơ hồ
    không ai không biết. Long thần, vốn chỉ là một Chân thần bình thường ..
    thế mà được coi trọng như Chủ thần . - A tu la liền giải thích cho Đoạn
    Vân .

    - À, ta mang theo Thần Long giới chỉ đến đây, chẳng lẽ việc này có gì lạ?

    - Đương nhiên có vấn đề, hơn nữa lại còn là một vấn đề rất lớn. Có một
    pháp tắc không gian như thế này : tiểu không gian không thể tùy ý qua
    lại giữa hai đại không gian. Cái này cũng là đạo lý khi một không gian
    giới tử không thể có thêm một cái bên trong nó nữa .
    dịch vụ kế toán trọn gói giá rẻ
    eco green city
    học kế toán tại hải phòng
    khoá học kế toán thực hành

    học kế toán tại long biên
    trung tâm kế toán tại hà đông
    dịch vụ báo cáo tài chính
    dịch vụ kế toán thuế trọn gói
    eco green city nguyễn xiển
    goldmark city
    công ty làm dịch vụ kế toán

    chung cư 89 phùng hưng
    tiếng anh giao tiếp cho trẻ em

    - Vậy Long thần làm sao mà đem giới tử này xuống nhân giới được chứ ?

    Nghe thế, Đoạn Vân lại càng thêm mù mờ. Tên Tạp Tây Cách Nhĩ tựa hồ còn
    đem giới chỉ này đi qua tận Ma giới cơ mà .

    - Long thần là một đầu Thánh long. Thánh long Tạp Tây Cách Nhĩ này có
    thuộc tính không gian nhất định. Hơn nữa ma pháp không gian của Tạp Tây
    Cách Nhĩ cũng đã tu luyện tới bậc Chân thần trung giai. Nếu thêm vài vạn
    năm nữa, Long thần rất có có thể trở thành Chủ thần không gian kế tiếp.
    Bằng vào thuộc tính không gian của hắn, hắn tự nhiên có thể mang theo
    Long thần giới của hắn đi lại. - A tu la trả lời .

    Đoạn Vân cười cười, nói :

    ReplyDelete
  4. Free Classifieds Ads - Post Free Ads. Sale, Buy, Offer and other Services free Business listing. Feature Ads also get more traffic. Best Classifieds sites in India.
    Free Classifieds Ads

    ReplyDelete

  5. I can't believe I've never been to this site before, but after going through some of the posts I realized it's new to me. Anyhow, I'm glad I found it and I'll be bookmarking and checking back often. You can fill your visa application form online within 5 to 10 minutes and pay your visa cost once you complete the form. The cost of Indian e visa depends on your nationality and visa type.

    ReplyDelete

  6. Hello all , Many people ask, What is the Indian visa photo size? You can get more info about India visa photo size via our Indian e page.

    ReplyDelete
  7. Hey there! Wonderful post! Many people ask, How to apply for a Turkey e visa? Citizens of eligible countries are allowed to apply and obtain a Turkey evisa after the submission of an online application. Eligible travelers only need a good internet connection and a computer, laptop or tablet to complete and submit a visa application

    ReplyDelete